[Kovove materialy - Metallic materials]
    Fri - October 04, 2024 - 06:28 No. of hits : 1788104 ISSN 1338-4252 (online) ISSN 0023-432X (printed)
© Institute of Materials and Machine Mechanics, Slovak Academy of Sciences, Bratislava, Slovak Republic

VOLUME 48 (2010), Issue 3

Al-Cu alloy formation by aluminium underpotential deposition from AlCl3+NaCl melts on copper substrate
RADOVIC, B. S., CVETKOVIC, V. S., EDWARDS, R. A. H., JOVICEVICJ. N.
Key words: aluminium-copper alloys, underpotential deposition, diffusion, microscopy and microanalysis techniques, Gibbs energy of formation, kinetics
vol. 48 (2010), no. 3, pp. 159 - 171
DOI: 10.4149/km_2010_3_159
[open abstract] Article   |   [open article.pdf] Full Text (433 kB)

Microstructural characterization and phase constituents near the interfaces of TiC-Al2O3/Q235 diffusion bonds
HUANG, W. Q., LI, Y., WANG, J.
Key words: TiC-Al2O3/Q235 joint, diffusion bonding, microstructure, phase constituents
vol. 48 (2010), no. 3, pp. 173 - 177
DOI: 10.4149/km_2010_3_173
[open abstract] Article   |   [open article.pdf] Full Text (281 kB)

An investigation into the effect of welding current on the plasma arc welding of pure titanium
KAHRAMAN, N., TASKIN, M., GULENC, B., DURGUTLU, A.
Key words: plasma arc welding, titanium, welding current
vol. 48 (2010), no. 3, pp. 179 - 184
DOI: 10.4149/km_2010_3_179
[open abstract] Article   |   [open article.pdf] Full Text (406 kB)

Comparison of dynamic mechanical properties of non-superheated and superheated A357 alloys
MAZLEE, M. N., SHAMSUL, J. B, KAMARUDIN, H.
Key words: A357, melt superheat treatment, grain boundary damping
vol. 48 (2010), no. 3, pp. 185 - 190
DOI: 10.4149/km_2010_3_185
[open abstract] Article   |   [open article.pdf] Full Text (287 kB)

Influence of fading and stirring on the performance of the AlTi5B1 and AlTi3C0.15 grain refiners in an Al-Fe alloy
NAGLIC, I.
Key words: aluminium alloy, solidification, grain refining, fading, stirring
vol. 48 (2010), no. 3, pp. 191 - 196
DOI: 10.4149/km_2010_3_191
[open abstract] Article   |   [open article.pdf] Full Text (210 kB)

Minimum fusion zone size required to ensure pullout failure mode of resistance spot welds during tensile-shear test
POURANVARI, M., MARASHI, S. P. H.
Key words: resistance spot welding, failure mode, fusion zone size
vol. 48 (2010), no. 3, pp. 197 - 202
DOI: 10.4149/km_2010_3_197
[open abstract] Article   |   [open article.pdf] Full Text (310 kB)

A study on wear and corrosion behaviour of thermally sprayed alumina-titania composite coatings on aluminium alloys
MINDIVAN, H.
Key words: aluminium, coating, corrosion, thermal spray, wear
vol. 48 (2010), no. 3, pp. 203 - 210
DOI: 10.4149/km_2010_3_203
[open abstract] Article   |   [open article.pdf] Full Text (1239 kB)

Effect of Ce on microstructures and mechanical properties of as-cast Mg-8Li-1Al alloys
ZHANG, M., MENG, X., WU, R., CUI, CH., WU, L.
Key words: Mg-Li alloy, Ce, microstructures, mechanical properties, Brinell hardness
vol. 48 (2010), no. 3, pp. 211 - 216
DOI: 10.4149/km_2010_3_211
[open abstract] Article   |   [open article.pdf] Full Text (604 kB)

Info: 8 records found.

[IMMS SAS]      UMMS SAV - Bratislava (SK) Personal data Protection   ver. 1.8.0      [go to HOME PAGE]
Full title of this journal is bilingual: Kovové materiály - Metallic Materials.
The official abbreviation in accordance with JCR ISI is Kovove Mater.


Article abstracts updated: 2024-07-25 13:22      
Articles in press revised: 2024-10-02 12:10     
Full text pdf uploaded: 2024-07-25 13:23    
Information updated: 2023-04-19 16:14   
Code last revised: 2024-03-06 11:13  

© OldSoft, 2004, …, 2024